Here is my log file, any help or tips would be greatly appreciated. I have run into a bit of a snag and I think it is the root cause of the problem. I have been playing with the script a bit trying to track down this error and figure out how I could solve this problem. All of the shades seem to have random problems, they sometimes move just a little bit when I send the open or close command, not all the shades, sometimes only one shade has this problem and sometimes a few more.
Indigo 7 somfi driver#
I have 7 total windows that I am utilizing this driver on. I have the same shades as mentioned in this thread. Really would like some help with troubleshooting. I always worried about it failing on me and having to replace it. I was lucky enough to find an online site had it for sale for a total or $89. When I was first started looking for the ZRTSI Bridge about 4 yrs ago, everybody wanted around $250 for them. I've been wanting to move away from the ZRTSI Bridge for a long while anyway. So far everything has been working great. I replaced all three with the iBlinds Z-Wave tilt motor kit, with Solar panel.
Indigo 7 somfi plus#
It worked about half the time, other times it would take 20 to 40 minutes before IFTTT would send the command to close the blinds.Ībout 2 months ago I gave up on using the Somfy tilt motors and ZRTSI Bridge, plus the Somfy MyLink, have all of it sitting in a box in my basement. That would have save me a lot of headaches, and money.Ībout two months after my post back in July, someone mention about using the Somfy MyLink to control my ZRTSI Bridge with Hubitat via IFTTT. I was expecting just to add it to Hubitat and have it working. I was so use to how it was setup and working fine in ST. * 1.0.0 Multi-tile, Window Shade Capability, Device Handler attempts to maintain state * 1.0.1 Add Blinds support by edit device to set to blinds type * 1.0.2 Added runIn timer for movement vs. * 1.0.3 Expanded runIn timer for movement and completed states * 1.0.4 Sync commands for cases where blinds respond to multiple channels (all vs. * 1.0.7 Few updates (be sure to go into each device, select settings (gear), and hit done imnotbob/somfy-shades/blob/master/devicetypes/imnotbob/somfy-shades.src/oovy /** Dim to 50% and it moves your shades to the my/favorite position. I used this device handler that was developed for SmartThings and replaced "physicalgraph" with "hubitat" and it works. I was trying to get the favorite position to work as well, and found a solution. Is it possible someone has a Z-wave dimmer or z-wave shade source that I could start with and modify? Is a new driver the way to go about this? I can't find a way in RuleMachine to issue the "stopLevelChange" command, otherwise I'd try and go that route. (Accomplished now just using a generic z-wave switch or shade)ģ)Dimmer/shade position is set to between 30% open and 60%, don't issue an "Up" or "Down" command, send a "stopLevelChange" message. (Accomplished now just using a generic z-wave switch or shade)Ģ)If the dimmer/shade switch is turned on, issue the "Down" command. Right now, I'm thinking the best way to accomplish this would be to create a driver that does the following:ġ)If the dimmer/shade switch is turned off, issue the "Up" command. I've tried messing around and have not found a way to expose this to Alexa/Homebridge. If I change the driver to use "Generic Z-Wave Dimmer", clicking on "stopLevelChange" in the Hubitat interface, my shade will go the the "Favorite" position. I really want to be able to also use the "Stop" command to automate going to a "Favorite" position. I can also expose the shade to HomeKit and Alexa via MakerAPI and Alexa built in apps. Right now I can use the "Generic Z-Wave Shade" Device driver and it exposes "Up" and "Down" functionality. I've got some z-wave shades(Specifically they are Somfy shades using a Somfy ZRTSI Bridge) that respond to the following Z-wave commands:ģ)Stop (When not moving, this will cause the shade to go to a "Favorite" position, so this is kind of dual function)
0 kommentar(er)
